|
|
|
|
|
|
|
|
|
|
|
|
|
Ford 8" & 9" trac loc cross shaft - cross pin
fits 9 ich Ford Mini spools also
|
NEW! PEM Gear Lube 75-140w Full Synthetic 1 quart
Tested in 2023 and 2024 to reduce rear end temperatures
|
28 Spline Mini Spool 9" Ford
WARNING: Cancer And Reproductive Harm-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
31" Spline Mini Spool 9" Ford
|
9 inch Ford Pilot bearing for nodular iron and aluminum cases
|
Ford 9' Trac Loc Complete Rebuild Kit 31; includes Clutch Set, springs, pins & all internal parts
Specify 28 spline or 31 spline
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ford 9" 1310 Short Narrow Forged Black Yoke
We suggest to also purchase the N1-0089L longer 1310 u bolts we sell
Uses 1310 series u joint - 3 7/32" wide with 1 1/16" OD caps (u joint not included).
|
Ford 9" 1330 Short Wide Rear End Yoke
- U-joint that fits this yoke is a 1330 Cleveland, 1-1/8" cap x 3-5/8" across (not included).
- cast yoke with dust shield
- 4 1/4" total length center of u-joint ot end of yoke
|
Ford 9" 1310 Short Narrow Forged Black Yoke Machined for a Daytona Pinion Support.
This yoke is shorter becayse the Dayton Pinion Support has a wider bearing
We suggest to also purchase the N1-0089L longer 1310 u bolts we sell.
Uses a 1310 series u-joint ( 3 7/32" wide with 1 1/16" outside diameter caps)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mini Spool for 10 bolt GM 7.5" ring & pinion. These are for car rear ends.
|
30
Spline Mini Spool 12 Bolt GM Car
30 spline Mini Spool for 12 Bolt
GM Rear (passenger car)
|
|
|
28 Spline Mini Spool 8.5" GM
only fits GM Car Rear Ends
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
30 Spline Mini Spool for Dana 44..
|
New! 28 spline 7.5" GM Mini Spool so you can install Ford 28 spline axles in
your 7.5" GM rear end.
Legal for Southern Sport Mods
|
FS28DS - 28 spline - 8.5 lbs.
Drag Spool will fit a stock 2.891" carrier bearing case
Tapered Spline Body for Strength
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ford 9" Cast Daytona Support, no races
|
Ford 9" 1350 28 Spline Forged Chrome Moly Yoke
fits 1350 series u-joints (3 5/8" wide x 1 3/16" OD caps)
manufactured to fit a Daytona Pinion Support and has dust shield.
|
Chevy 12 Bolt 1350 Forged Yoke
this yoke only fits a 12 bolt car rear end
fits 1350 series u-joint ( 3 5/8" wide x 1 3/16" outside diamater cap)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ford 8.8" 1330 Forged Yoke 1-1/8" caps x 3-5/8" wide
|
Ford 9" 1350 35 Spline Forged Yoke.
|
1350 GM 10 Bolt 1350 Forged Yoke
for 8.5" General Motors Rear End
Only fits Car rear ends
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dana 60 1350 Forged Yoke
fits 1350 u-joint ( 3 5/8" wide x 1 3/16" outside diameter cap)
|
Ford 9" Aluminum Daytona Pinion Support
Races not included
|
Drilled straight body spool for 9" Ford
28 spline
6.25 lbs.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ford
9" Cast Daytona Support with Races
|
|
Ford 9" 1350 28 Spline New BILLET Yoke
Chrome Moly
|
Complete Bearing and Installation Kit for 9” Ford with Carrier Bearings,
Pinion Bearings, pilot bearing, solid pinion spacer, shims, nuts, pinion seal,
Ring gear bolts and gasket. 1.78 ID, 2.89” OD
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Chrome Moly Machined Billet Yoke for 35 spline large pinion
9" Ford fits 1350 Series u joint (3 5/8" wide x 1 3/16" caps)
2.1255" OD for seal surface
|
FS35SB Steel Spool - 33 spline - 8.3 lbs.
Spool has 1.78" Bearing Journals for Stock Size case with 2.891" or 3.06" carrier bearing size.
Tapered Spline Body for Strength
|
Ford 9" Alum. Daytona Pinion Support
Small Bearing with Races installed
|
|
|
